Table of Contents
Why flue shut off dampers are used?
In a chimney flue, a damper closes off the flue to keep the weather (and birds and other animals) out and warm or cool air in. This is usually done in the summer, but also sometimes in the winter between uses. In some cases, the damper may also be partly closed to help control the rate of combustion.
What are damper valves?
Damper valves are a vital part of any air circulation system. Superior to simple fan control systems of old, damper valves allow for accurate directional flow control. Damper valves can also control the amount of material that is allowed to pass through a system and can work to isolate equipment from gas or air flow.
Where is the damper located?
Typically in most homes, your HVAC dampers are located in the main supply trunks. The supply trunks are the parts of the ductwork that are blowing warm air or cold air depending on the season.
How does a motorized damper work?
How does a motorized fire damper work? Motorized fire dampers work by automatically shutting off the air supply to an affected part of the HVAC network which prevents the spread of smoke and fire through the duct system. These dampers are typically activated in one or more ways.
What is the difference between a damper and a valve?
Let’s start by looking at our two current definitions of these tags: damper : Damper position measured from 0% (fully closed) to 100% (fully open). valve : Marker tag on point which indicates a valve used to regulate or control the flow or pressure of a fluid.
How do you tell if a damper is open or closed?
Conduct a visual check. Lean in under your chimney just outside of your wood burning stove. You should find a metal device just within the chimney or flue opening. The damper is open if you can see through the damper up to your chimney. If you only see a metal plate, the damper is in a closed position.
How long does a damper motor last?
15 years
With proper maintenance and care, your HVAC damper motor can last you as long as your system lasts. That means damper motors can last 15 years, but like any electrical device, they’re prone to malfunction if neglected.
How do you check a motorized damper?
Put the damper into an open position and check the registers once again to see if the airflow starts. If the damper is closed and you are feeling low airflow, or none at all, it is most likely a bad damper. For the automatic control damper, turn your HVAC system on. Check for airflow in the registers.
What are the different types of dampers?
Types of Dampers in HVAC
- Introduction to Different Types of Dampers.
- Butterfly Flat Dish Damper.
- Blade Dampers.
- Guillotine Dampers.
- Louver Dampers.
- Inlet Vane Dampers.
How does a damper actuator work?
Part of a heating, ventilation, and air conditioning (HVAC) system, a damper actuator controls the opening and closing of a damper. Opening the damper allows air from outside a building to enter, in order to cool the interior, or it can close to contain the inside air.
Should gas fireplace flue be open or closed?
Our research shows that the flue on a gas fireplace should remain open during use or when the pilot light is lit. If the flue is closed in either instance, you risk a greater chance of carbon monoxide poisoning or a spark induced structure fire due to a buildup of toxins emitted by propane or natural gas burners.
What are flue gas dampers?
The medium often concerns flue gases and exhaust gases that are discharged or fed at low pressures. The shape and size of flue gas ducts are highly diverse, which leads to the fact that the manufacture of flue gas dampers often involves customisation. In cooperation with our partner Ammtech Srl.
Why choose Hanwel for your flue gas dampers?
The shape and size of flue gas ducts are highly diverse, which leads to the fact that the manufacture of flue gas dampers often involves customisation. In cooperation with our partner Ammtech Srl. Hanwel supplies a wide range of flue gas valves.
Do you offer different types of flue gas valves?
We can offer different types of flue gas valves depending on your situation and the local requirements. At all times, a GAD drawing and 3D file is included in the supply and will be sent for approval.
What are flue gas ducts?
Flue gas ducts are characterised by large to very large sizes and high to extremely high temperatures. The medium often concerns flue gases and exhaust gases that are discharged or fed at low pressures.